2019-10-07T22:15:55.764Z,1570486555.764 [Supervisor](IMPORTANT): Reading configuration overrides from Data/persisted.cfg 2019-10-07T22:16:00.850Z,1570486560.850 [SBIT](IMPORTANT): git: 2019-10-03_bsd 2019-10-07T22:16:00.850Z,1570486560.850 [SBIT](IMPORTANT): Kernel Release: 2.6.27.8 2019-10-07T22:16:00.850Z,1570486560.850 [SBIT](IMPORTANT): Kernel Version:#1 PREEMPT Thu Feb 21 11:17:40 PST 2019 2019-10-07T22:16:02.342Z,1570486562.342 [RudderServo](FAULT): Rudder failed to initialize 2019-10-07T22:16:42.500Z,1570486602.500 [SBIT](IMPORTANT): Beginning Startup BIT 2019-10-07T22:16:42.530Z,1570486602.530 [CBIT](IMPORTANT): Beginning ground fault scan 2019-10-07T22:16:53.254Z,1570486613.254 [CBIT](IMPORTANT): Ground fault detected mA: CHAN A0 (Batt): 0.447279 CHAN A1 (24V): -0.178098 CHAN A2 (12V): 0.327563 CHAN A3 (5V): 0.103058 CHAN B0 (3.3V): 0.063063 CHAN B1 (3.15aV): 0.065521 CHAN B2 (3.15bV): 0.068382 CHAN B3 (GND): -0.012066 OPEN: 0.015950 Full Scale Calc: 4.765 mA, -1.589 mA 2019-10-07T22:17:36.443Z,1570486656.443 [SBIT](IMPORTANT): SBIT PASSED 2019-10-07T22:17:36.539Z,1570486656.539 [CommandLine](IMPORTANT): got command configSet list 2019-10-07T22:17:36.539Z,1570486656.539 [CommandLine](IMPORTANT): Listing configuration overrides from Data/persisted.cfg 2019-10-07T22:17:36.540Z,1570486656.540 [CommandLine](IMPORTANT): CBIT.abortDepth=300 meter; 2019-10-07T22:17:36.540Z,1570486656.540 [CommandLine](IMPORTANT): CBIT.gf24Offset=143 microampere; 2019-10-07T22:17:36.540Z,1570486656.540 [CommandLine](IMPORTANT): CBIT.stopDepth=290 meter; 2019-10-07T22:17:36.540Z,1570486656.540 [CommandLine](IMPORTANT): DAT.loadAtStartup=0 bool; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Express linearApproximation BackSeatDriver.biolum_dinoflagellate_proxy 1000000000.000000 none; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Express none BackSeatDriver.biolum_jelly_proxy; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Express none RDI_Pathfinder.height_above_sea_floor; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Express linearApproximation Tracking.range_to_contact 10.000000 meter; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Express none WetLabsUBAT.biolum_potential; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Express none WetLabsUBAT.flow_rate; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Express linearApproximation height_above_sea_floor 10.000000 meter; 2019-10-07T22:17:36.541Z,1570486656.541 [CommandLine](IMPORTANT): Normal linearApproximation BackSeatDriver.biolum_jelly_proxy 1000000.000000 none; 2019-10-07T22:17:36.542Z,1570486656.542 [CommandLine](IMPORTANT): Normal linearApproximation WetLabsUBAT.biolum_potential 1000000.000000 none; 2019-10-07T22:17:36.542Z,1570486656.542 [CommandLine](IMPORTANT): RDI_Pathfinder.loadAtStartup=0 bool; 2019-10-07T22:17:36.542Z,1570486656.542 [CommandLine](IMPORTANT): VerticalControl.buoyancyNeutral=191 cubic_centimeter; 2019-10-07T22:17:36.542Z,1570486656.542 [CommandLine](IMPORTANT): VerticalControl.massDefault=5.5 millimeter; 2019-10-07T22:17:36.834Z,1570486656.834 [MissionManager](IMPORTANT): Started mission Startup 2019-10-07T22:18:40.749Z,1570486720.749 [MissionManager](IMPORTANT): Started mission Default 2019-10-07T22:25:35.627Z,1570487135.627 [Default:CheckIn:E](IMPORTANT): Default mission has been running for 6.907932 min 2019-10-07T22:26:25.060Z,1570487185.060 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3290, MT Status=1, MTMSN=121 2019-10-07T22:26:25.650Z,1570487185.650 [CommandLine](IMPORTANT): got command ! echo i > /dev/loadC1 2019-10-07T22:32:32.553Z,1570487552.553 [Default:CheckIn:E](IMPORTANT): Default mission has been running for 13.856396 min 2019-10-07T22:38:07.819Z,1570487887.819 [Default:CheckIn:E](IMPORTANT): Default mission has been running for 19.444529 min 2019-10-07T22:38:30.556Z,1570487910.556 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3299, MT Status=1, MTMSN=122 2019-10-07T22:38:31.106Z,1570487911.106 [CommandLine](IMPORTANT): got command gfscan 2019-10-07T22:38:31.402Z,1570487911.402 [CBIT](IMPORTANT): Beginning ground fault scan 2019-10-07T22:38:44.440Z,1570487924.440 [CBIT](IMPORTANT): Ground fault detected mA: CHAN A0 (Batt): -0.024980 CHAN A1 (24V): -0.167420 CHAN A2 (12V): -0.007938 CHAN A3 (5V): -0.001495 CHAN B0 (3.3V): 0.000426 CHAN B1 (3.15aV): 0.000466 CHAN B2 (3.15bV): -0.000052 CHAN B3 (GND): 0.001848 OPEN: 0.004531 Full Scale Calc: 4.765 mA, -1.589 mA 2019-10-07T22:44:34.005Z,1570488274.005 [Default:CheckIn:E](IMPORTANT): Default mission has been running for 25.880988 min 2019-10-07T22:50:07.641Z,1570488607.641 [Default:CheckIn:E](IMPORTANT): Default mission has been running for 31.441331 min 2019-10-07T22:50:26.740Z,1570488626.740 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3308, MT Status=1, MTMSN=123 2019-10-07T22:50:27.468Z,1570488627.468 [CommandLine](IMPORTANT): got command load ./Missions/Science/profile_station.xml 2019-10-07T22:50:28.903Z,1570488628.903 [CommandLine](IMPORTANT): Loaded ./Missions/Science/profile_station.xml 2019-10-07T22:50:34.381Z,1570488634.381 [CommandLine](IMPORTANT): got command set profile_station.MissionTimeout 12.000000 hour 2019-10-07T22:50:34.382Z,1570488634.382 [CommandLine](IMPORTANT): got command set profile_station.Lat 36.712109 degree 2019-10-07T22:50:34.383Z,1570488634.383 [CommandLine](IMPORTANT): got command set profile_station.Lon -122.187027 degree 2019-10-07T22:50:34.384Z,1570488634.384 [CommandLine](IMPORTANT): got command set profile_station.Radius 2000.000000 meter 2019-10-07T22:50:34.384Z,1570488634.384 [CommandLine](IMPORTANT): got command run 2019-10-07T22:50:34.446Z,1570488634.446 [CommandLine](IMPORTANT): Running 2019-10-07T22:50:34.462Z,1570488634.462 [MissionManager](IMPORTANT): Started mission profile_station 2019-10-07T22:50:35.326Z,1570488635.326 [BuoyancyServo](FAULT): Buoyancy getPosition uart error.serial timeout 2019-10-07T22:50:57.732Z,1570488657.732 [BackSeatDriver](IMPORTANT): photon: running biolum proxies application. 2019-10-07T23:52:18.564Z,1570492338.564 [ThrusterServo](FAULT): Invalid EZ Servo response:"" 2019-10-08T00:01:55.228Z,1570492915.228 [NAL9602](IMPORTANT): SBD MO Status=0, MOMSN=3318, MT Status=1, MTMSN=124 2019-10-08T00:01:55.993Z,1570492915.993 [CommandLine](IMPORTANT): got command configSet WetLabsUBAT.loadAtStartup 1.000000 bool 2019-10-08T00:01:55.993Z,1570492915.993 [CommandLine](FAULT): configSet WetLabsUBAT.loadAtStartup without persist will have no effect. 2019-10-08T00:02:15.130Z,1570492935.130 [NAL9602](CRITICAL): Packet size is not N*16+4: 0x0 2019-10-08T00:02:15.130Z,1570492935.130 [NAL9602](CRITICAL): Failed to parse uplink message: 2019-10-08T00:02:15.172Z,1570492935.172 [CommandLine](FAULT): Scheduling is paused 2019-10-08T00:02:15.886Z,1570492935.886 [MissionManager](IMPORTANT): Started mission Default 2019-10-08T00:03:31.761Z,1570493011.761 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3320, MT Status=1, MTMSN=125 2019-10-08T00:03:32.467Z,1570493012.467 [CommandLine](IMPORTANT): got command load ./Missions/Science/profile_station.xml 2019-10-08T00:03:33.638Z,1570493013.638 [CommandLine](IMPORTANT): Loaded ./Missions/Science/profile_station.xml 2019-10-08T00:03:38.820Z,1570493018.820 [CommandLine](IMPORTANT): got command set profile_station.MissionTimeout 16.000000 hour 2019-10-08T00:03:38.821Z,1570493018.821 [CommandLine](IMPORTANT): got command set profile_station.Lat 36.712109 degree 2019-10-08T00:03:38.822Z,1570493018.822 [CommandLine](IMPORTANT): got command set profile_station.Lon -122.187027 degree 2019-10-08T00:03:38.823Z,1570493018.823 [CommandLine](IMPORTANT): got command set profile_station.Radius 2000.000000 meter 2019-10-08T00:03:38.823Z,1570493018.823 [CommandLine](IMPORTANT): got command run 2019-10-08T00:03:38.825Z,1570493018.825 [CommandLine](IMPORTANT): Running 2019-10-08T00:03:38.904Z,1570493018.904 [MissionManager](IMPORTANT): Started mission profile_station 2019-10-08T00:03:39.718Z,1570493019.718 [BuoyancyServo](FAULT): Buoyancy getPosition uart error.serial timeout 2019-10-08T00:03:59.068Z,1570493039.068 [BackSeatDriver](IMPORTANT): photon: running biolum proxies application. 2019-10-08T02:13:29.414Z,1570500809.414 [ThrusterServo](FAULT): Invalid EZ Servo response:"" 2019-10-08T02:36:54.505Z,1570502214.505 [NAL9602](FAULT): MT Queue status failed to be acquired within timeout. Will not retry this session. 2019-10-08T02:44:36.558Z,1570502676.558 [ElevatorOffsetCalculator](IMPORTANT): Completed estimation for commanded vars: speed 1.00 m/s, pitch -20.00 deg, mass-position 5.50 mm. Average elevator angle=0.790455 +/- 0.098331 deg (conf. level 99.90%, sigma: 0.368515 deg). 2019-10-08T03:04:28.182Z,1570503868.182 [ThrusterServo](FAULT): Unknown EZ Servo Error: 10 2019-10-08T03:09:58.982Z,1570504198.982 [RudderServo](FAULT): Rudder uart error - getPosition..serial timeout 2019-10-08T04:04:22.510Z,1570507462.510 [ElevatorOffsetCalculator](IMPORTANT): Completed estimation for commanded vars: speed 1.00 m/s, pitch 20.00 deg, mass-position 5.50 mm. Average elevator angle=-2.886689 +/- 0.095761 deg (conf. level 99.90%, sigma: 0.337913 deg). 2019-10-08T04:38:44.617Z,1570509524.617 [CBIT](IMPORTANT): Beginning ground fault scan 2019-10-08T04:38:55.529Z,1570509535.529 [CBIT](IMPORTANT): Ground fault detected mA: CHAN A0 (Batt): 0.192980 CHAN A1 (24V): -0.186186 CHAN A2 (12V): 0.170602 CHAN A3 (5V): 0.041902 CHAN B0 (3.3V): 0.035815 CHAN B1 (3.15aV): 0.021595 CHAN B2 (3.15bV): 0.022025 CHAN B3 (GND): -0.016541 OPEN: 0.010670 Full Scale Calc: 4.765 mA, -1.589 mA 2019-10-08T06:45:46.276Z,1570517146.276 [ElevatorOffsetCalculator](IMPORTANT): Completed estimation for commanded vars: speed 1.00 m/s, pitch -20.00 deg, mass-position 5.50 mm. Average elevator angle=0.678077 +/- 0.091767 deg (conf. level 99.90%, sigma: 0.347445 deg). 2019-10-08T08:46:35.774Z,1570524395.774 [ThrusterServo](FAULT): Invalid EZ Servo response:"" 2019-10-08T09:00:07.554Z,1570525207.554 [ThrusterServo](FAULT): Invalid EZ Servo response:"" 2019-10-08T09:08:43.119Z,1570525723.119 [ThrusterServo](FAULT): getVelocity uart error serial timeout 2019-10-08T09:08:43.119Z,1570525723.119 [ThrusterServo](FAULT): Thruster uart error: serial timeout 2019-10-08T09:27:20.980Z,1570526840.980 [NAL9602](FAULT): Verify xmit timeout failure. 2019-10-08T10:38:55.836Z,1570531135.836 [CBIT](IMPORTANT): Beginning ground fault scan 2019-10-08T10:39:07.208Z,1570531147.208 [CBIT](IMPORTANT): Ground fault detected mA: CHAN A0 (Batt): 0.188531 CHAN A1 (24V): -0.168852 CHAN A2 (12V): 0.166281 CHAN A3 (5V): 0.054306 CHAN B0 (3.3V): 0.047292 CHAN B1 (3.15aV): 0.027145 CHAN B2 (3.15bV): 0.024624 CHAN B3 (GND): -0.016968 OPEN: 0.012321 Full Scale Calc: 4.765 mA, -1.589 mA 2019-10-08T13:43:43.240Z,1570542223.240 [BuoyancyServo](FAULT): Reading outside of valid range:0.000000 2019-10-08T13:43:43.240Z,1570542223.240 [BuoyancyServo](FAULT): Buoyancy engine reporting null position 2019-10-08T14:58:29.092Z,1570546709.092 [NAL9602](FAULT): MT Queue status failed to be acquired within timeout. Will not retry this session. 2019-10-08T14:59:07.027Z,1570546747.027 [NAL9602](FAULT): LCB fault: LCB Watchdog Reset. Invalid Command. Software Overcurrent. 2019-10-08T15:11:27.433Z,1570547487.433 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3655, MT Status=1, MTMSN=126 2019-10-08T15:11:28.182Z,1570547488.182 [CommandLine](IMPORTANT): got command configSet WetLabsUBAT.loadAtStartup 0.000000 bool 2019-10-08T15:11:28.182Z,1570547488.182 [CommandLine](FAULT): configSet WetLabsUBAT.loadAtStartup without persist will have no effect. 2019-10-08T15:11:29.119Z,1570547489.119 [WetLabsUBAT](IMPORTANT): Stopping now due to load at startup. No immediate restart required. 2019-10-08T15:17:20.925Z,1570547840.925 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3668, MT Status=1, MTMSN=127 2019-10-08T15:17:21.651Z,1570547841.651 [CommandLine](IMPORTANT): got command load ./Missions/Science/profile_station.xml 2019-10-08T15:17:22.411Z,1570547842.411 [WetLabsBB2FL](FAULT): LCB fault: Software Overcurrent. 2019-10-08T15:17:22.969Z,1570547842.969 [CommandLine](IMPORTANT): Loaded ./Missions/Science/profile_station.xml 2019-10-08T15:17:28.227Z,1570547848.227 [CommandLine](IMPORTANT): got command set profile_station.MissionTimeout 16.000000 hour 2019-10-08T15:17:28.227Z,1570547848.227 [CommandLine](IMPORTANT): got command set profile_station.Lat 36.712109 degree 2019-10-08T15:17:28.228Z,1570547848.228 [CommandLine](IMPORTANT): got command set profile_station.Lon -122.187027 degree 2019-10-08T15:17:28.229Z,1570547848.229 [CommandLine](IMPORTANT): got command set profile_station.Radius 2000.000000 meter 2019-10-08T15:17:28.230Z,1570547848.230 [CommandLine](IMPORTANT): got command run 2019-10-08T15:17:28.231Z,1570547848.231 [CommandLine](IMPORTANT): Running 2019-10-08T15:17:28.297Z,1570547848.297 [MissionManager](IMPORTANT): Started mission profile_station 2019-10-08T15:17:29.138Z,1570547849.138 [BuoyancyServo](FAULT): Buoyancy getPosition uart error.serial timeout 2019-10-08T16:30:40.996Z,1570552240.996 [NAL9602](IMPORTANT): SBD MO Status=0, MOMSN=3681, MT Status=1, MTMSN=128 2019-10-08T16:30:41.579Z,1570552241.579 [CommandLine](IMPORTANT): got command schedule clear 2019-10-08T16:30:41.579Z,1570552241.579 [CommandLine](IMPORTANT): #Cleared scheduled commands:0 2019-10-08T16:30:41.579Z,1570552241.579 [CommandLine](IMPORTANT): got command schedule resume 2019-10-08T16:30:41.580Z,1570552241.580 [CommandLine](IMPORTANT): Scheduling is resumed 2019-10-08T16:39:07.338Z,1570552747.338 [CBIT](IMPORTANT): Beginning ground fault scan 2019-10-08T16:39:18.249Z,1570552758.249 [CBIT](IMPORTANT): Ground fault detected mA: CHAN A0 (Batt): 0.265039 CHAN A1 (24V): -0.168240 CHAN A2 (12V): 0.209540 CHAN A3 (5V): 0.074900 CHAN B0 (3.3V): 0.051185 CHAN B1 (3.15aV): 0.050211 CHAN B2 (3.15bV): 0.051649 CHAN B3 (GND): -0.000721 OPEN: 0.015720 Full Scale Calc: 4.765 mA, -1.589 mA 2019-10-08T18:56:22.186Z,1570560982.186 [NAL9602](IMPORTANT): SBD MO Status=0, MOMSN=3699, MT Status=1, MTMSN=129 2019-10-08T18:56:22.782Z,1570560982.782 [CommandLine](IMPORTANT): got command ! echo i > /dev/loadC1 2019-10-08T18:56:35.230Z,1570560995.230 [BuoyancyServo](FAULT): Buoyancy getPosition uart error.serial timeout 2019-10-08T18:56:37.516Z,1570560997.516 [BuoyancyServo](FAULT): LCB fault: Current Limiter Activated. 2019-10-08T19:00:54.427Z,1570561254.427 [NAL9602](FAULT): Verify xmit timeout failure. 2019-10-08T19:00:55.227Z,1570561255.227 [NAL9602](FAULT): LCB fault: Software Overcurrent. 2019-10-08T20:15:49.456Z,1570565749.456 [NAL9602](FAULT): MT Queue status failed to be acquired within timeout. Will not retry this session. 2019-10-08T21:33:55.255Z,1570570435.255 [Radio_Surface](FAULT): LCB fault: Software Overcurrent. 2019-10-08T22:39:18.580Z,1570574358.580 [CBIT](IMPORTANT): Beginning ground fault scan 2019-10-08T22:39:29.565Z,1570574369.565 [CBIT](IMPORTANT): Ground fault detected mA: CHAN A0 (Batt): -0.029541 CHAN A1 (24V): -0.167351 CHAN A2 (12V): -0.007327 CHAN A3 (5V): -0.002645 CHAN B0 (3.3V): -0.000109 CHAN B1 (3.15aV): -0.000222 CHAN B2 (3.15bV): -0.000520 CHAN B3 (GND): 0.002795 OPEN: 0.004041 Full Scale Calc: 4.765 mA, -1.589 mA 2019-10-09T01:12:13.608Z,1570583533.608 [NAL9602](IMPORTANT): SBD MO Status=0, MOMSN=3737, MT Status=1, MTMSN=130 2019-10-09T01:12:14.356Z,1570583534.356 [CommandLine](IMPORTANT): got command configSet WetLabsUBAT.loadAtStartup 1.000000 bool 2019-10-09T01:12:14.356Z,1570583534.356 [CommandLine](FAULT): configSet WetLabsUBAT.loadAtStartup without persist will have no effect. 2019-10-09T01:12:33.161Z,1570583553.161 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3738, MT Status=1, MTMSN=131 2019-10-09T01:12:33.876Z,1570583553.876 [CommandLine](IMPORTANT): got command load ./Missions/Science/profile_station.xml 2019-10-09T01:12:34.818Z,1570583554.818 [WetLabsBB2FL](FAULT): LCB fault: Software Overcurrent. 2019-10-09T01:12:35.671Z,1570583555.671 [CommandLine](IMPORTANT): Loaded ./Missions/Science/profile_station.xml 2019-10-09T01:12:41.099Z,1570583561.099 [CommandLine](IMPORTANT): got command set profile_station.MissionTimeout 16.000000 hour 2019-10-09T01:12:41.100Z,1570583561.100 [CommandLine](IMPORTANT): got command set profile_station.Lat 36.712109 degree 2019-10-09T01:12:41.101Z,1570583561.101 [CommandLine](IMPORTANT): got command set profile_station.Lon -122.187027 degree 2019-10-09T01:12:41.102Z,1570583561.102 [CommandLine](IMPORTANT): got command set profile_station.Radius 2000.000000 meter 2019-10-09T01:12:41.103Z,1570583561.103 [CommandLine](IMPORTANT): got command run 2019-10-09T01:12:41.105Z,1570583561.105 [CommandLine](IMPORTANT): Running 2019-10-09T01:12:41.128Z,1570583561.128 [MissionManager](IMPORTANT): Started mission profile_station 2019-10-09T01:12:42.062Z,1570583562.062 [BuoyancyServo](FAULT): Buoyancy getPosition uart error.serial timeout 2019-10-09T01:17:56.958Z,1570583876.958 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T01:23:29.326Z,1570584209.326 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T01:29:01.653Z,1570584541.653 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T01:31:44.027Z,1570584704.027 [ThrusterServo](FAULT): Invalid EZ Servo response:"\377\r" 2019-10-09T01:34:33.974Z,1570584873.974 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T01:40:06.294Z,1570585206.294 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T01:40:06.351Z,1570585206.351 [CBIT](FAULT): Communications Fault in component: BackSeatDriver 2019-10-09T01:47:37.018Z,1570585657.018 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T01:53:09.346Z,1570585989.346 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T01:58:41.674Z,1570586321.674 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T02:04:13.997Z,1570586653.997 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T02:09:46.326Z,1570586986.326 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T02:09:46.446Z,1570586986.446 [CBIT](FAULT): Communications Fault in component: BackSeatDriver 2019-10-09T02:17:17.034Z,1570587437.034 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T02:22:49.353Z,1570587769.353 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T02:28:21.730Z,1570588101.730 [BackSeatDriver](FAULT): Failed to receive device response within the specified timeout. 2019-10-09T02:28:59.872Z,1570588139.872 [BackSeatDriver](IMPORTANT): photon: running biolum proxies application. 2019-10-09T03:50:44.517Z,1570593044.517 [NAL9602](FAULT): MT Queue status failed to be acquired within timeout. Will not retry this session. 2019-10-09T04:39:29.949Z,1570595969.949 [CBIT](IMPORTANT): Beginning ground fault scan 2019-10-09T04:39:40.872Z,1570595980.872 [CBIT](IMPORTANT): Ground fault detected mA: CHAN A0 (Batt): 0.259369 CHAN A1 (24V): -0.213221 CHAN A2 (12V): 0.207768 CHAN A3 (5V): 0.045150 CHAN B0 (3.3V): 0.034208 CHAN B1 (3.15aV): 0.030785 CHAN B2 (3.15bV): 0.036067 CHAN B3 (GND): -0.004768 OPEN: 0.011344 Full Scale Calc: 4.765 mA, -1.589 mA 2019-10-09T04:56:08.438Z,1570596968.438 [NAL9602](FAULT): received: +CSQ:0 OK55, 2, 0, 0, 0 OK 2019-10-09T05:03:44.689Z,1570597424.689 [NAL9602](IMPORTANT): SBD MO Status=1, MOMSN=3761, MT Status=1, MTMSN=132