2017-12-12T22:38:14.217Z,1513118294.217 [CBIT](CRITICAL): SIGSEGV: address not mapped to object
2017-12-12T22:38:14.218Z,1513118294.218 [CBIT](CRITICAL): Bad address: 0x0
2017-12-12T22:38:14.218Z,1513118294.218 [CBIT](CRITICAL): Backtrace: 
./bin/LRAUV(_ZN7PCaller20DefaultSignalHandlerEiP7siginfoPv+0x20) [0x1670e8]
Modules/BIT.so(_ZN4CBIT3runEv+0xc) [0x407e6cc8]
./bin/LRAUV(_ZN7PCaller10PThreadRunEPv+0xbc) [0x166c84]

2017-12-12T22:39:38.643Z,1513118378.643 [CBIT](CRITICAL): run-time exception #7
2017-12-12T22:39:38.643Z,1513118378.643 [CBIT](CRITICAL): Bad address: 0x4041E004
2017-12-12T22:39:38.643Z,1513118378.643 [CBIT](CRITICAL): Backtrace: 
./bin/LRAUV(_ZN7PCaller20DefaultSignalHandlerEiP7siginfoPv+0x20) [0x1670e8]

2017-12-12T22:38:07.267Z,1513118287.267 [Supervisor](FAULT): Ignoring configuration overrides from Data/persisted.cfg
2017-12-12T22:38:12.288Z,1513118292.288 [SBIT](IMPORTANT): git: 2017-11-20A-2-g40c84ee
2017-12-12T22:38:12.289Z,1513118292.289 [SBIT](IMPORTANT): Kernel Release: 2.6.27.8
2017-12-12T22:38:12.292Z,1513118292.292 [CBIT](FAULT): LAST RESTART WAS UNINTENTIONAL.
2017-12-12T22:38:23.367Z,1513118303.367 [Aanderaa_O2](FAULT): Timed out starting
2017-12-12T22:38:23.733Z,1513118303.733 [BuoyancyServo](FAULT): Buoyancy failed to initialize
2017-12-12T22:38:24.045Z,1513118304.045 [ElevatorServo](FAULT): Elevator failed to initialize
2017-12-12T22:38:24.353Z,1513118304.353 [RudderServo](FAULT): Rudder failed to initialize
2017-12-12T22:38:25.001Z,1513118305.001 [ThrusterServo](FAULT): Thruster failed to initialize
2017-12-12T22:38:25.629Z,1513118305.629 [MassServo](FAULT): Mass shifter EEPROM initialization uart error serial timeout
2017-12-12T22:38:25.811Z,1513118305.811 [ElevatorServo](FAULT): LCB fault:  Hardware Overcurrent Shutdown. Current Limiter Activated.
2017-12-12T22:38:25.851Z,1513118305.851 [RudderServo](FAULT): LCB fault:  Hardware Overcurrent Shutdown. Current Limiter Activated.
2017-12-12T22:38:26.205Z,1513118306.205 [MassServo](FAULT): LCB fault:  Hardware Overcurrent Shutdown. Current Limiter Activated.
2017-12-12T22:38:26.976Z,1513118306.976 [BuoyancyServo](FAULT): LCB fault:  Hardware Overcurrent Shutdown. Current Limiter Activated.
2017-12-12T22:38:30.938Z,1513118310.938 [PNI_TCM](FAULT): Failed to set parameters during initialization.
2017-12-12T22:38:33.315Z,1513118313.315 [AcousticModem_Benthos_ATM900](FAULT): failed to initialize, no bytes available on serial interface
2017-12-12T22:38:34.116Z,1513118314.116 [AcousticModem_Benthos_ATM900](FAULT): LCB fault:  Hardware Overcurrent Shutdown. Current Limiter Activated.
2017-12-12T22:39:15.762Z,1513118355.762 [SBIT](IMPORTANT): Beginning Startup BIT
2017-12-12T22:39:35.386Z,1513118375.386 [CommandLine](IMPORTANT): got command quit