2018-08-15T17:51:23.420Z,1534355483.420 [CBIT](CRITICAL): Environmental Failure. Press:14.703550 PSI. Humidity:44%. Temp:26 C. ABORTING MISSION
2018-08-15T17:51:40.394Z,1534355500.394 [CBIT](CRITICAL): Hardware Fault in component: MassServo
2018-08-15T17:52:35.604Z,1534355555.604 [SBIT](CRITICAL): SBIT FAILED
2018-08-15T17:51:08.810Z,1534355468.810 [Supervisor](IMPORTANT): Reading configuration overrides from Data/persisted.cfg
2018-08-15T17:51:13.053Z,1534355473.053 [SBIT](IMPORTANT): git: 2018-08-02-21-g63d70fd
2018-08-15T17:51:13.054Z,1534355473.054 [SBIT](IMPORTANT): Kernel Release: 2.6.27.8
2018-08-15T17:51:17.953Z,1534355477.953 [BuoyancyServo](FAULT): Invalid EZ Servo response:""
2018-08-15T17:51:17.954Z,1534355477.954 [BuoyancyServo](FAULT): Buoyancy engine reporting null position
2018-08-15T17:51:20.677Z,1534355480.677 [MassServo](FAULT): Invalid EZ Servo response:""
2018-08-15T17:51:20.678Z,1534355480.678 [MassServo](FAULT): Mass Shifter error waiting for homing. Uart error: serial timeout
2018-08-15T17:51:20.693Z,1534355480.693 [MassServo](FAULT): Invalid EZ Servo response:"6"
2018-08-15T17:51:23.734Z,1534355483.734 [Aanderaa_O2](FAULT): Timed out starting
2018-08-15T17:51:23.806Z,1534355483.806 [CommandLine](FAULT): Scheduling is paused
2018-08-15T17:51:24.535Z,1534355484.535 [Aanderaa_O2](FAULT): LCB fault: LCB Watchdog Reset. Invalid Command. Hardware Overcurrent Shutdown. Software Overcurrent. Current Limiter Activated.
2018-08-15T17:51:25.829Z,1534355485.829 [MassServo](FAULT): Invalid EZ Servo response:"\n"
2018-08-15T17:51:25.829Z,1534355485.829 [MassServo](FAULT): Mass Shifter error waiting for homing. Uart error: serial timeout
2018-08-15T17:51:26.297Z,1534355486.297 [MassServo](FAULT): Invalid EZ Servo response:"\n"
2018-08-15T17:51:30.454Z,1534355490.454 [MassServo](FAULT): Invalid EZ Servo response:"\n"
2018-08-15T17:51:30.454Z,1534355490.454 [MassServo](FAULT): Mass Shifter error waiting for homing. Uart error: serial timeout
2018-08-15T17:51:35.370Z,1534355495.370 [MassServo](FAULT): Invalid EZ Servo response:"\n"
2018-08-15T17:51:35.370Z,1534355495.370 [MassServo](FAULT): Mass Shifter error waiting for homing. Uart error: serial timeout
2018-08-15T17:51:35.838Z,1534355495.838 [MassServo](FAULT): Invalid EZ Servo response:"\n"
2018-08-15T17:51:35.850Z,1534355495.850 [Aanderaa_O2](FAULT): Timed out starting
2018-08-15T17:51:36.687Z,1534355496.687 [Aanderaa_O2](FAULT): LCB fault: LCB Watchdog Reset. Invalid Command. Hardware Overcurrent Shutdown. Software Overcurrent. Current Limiter Activated.
2018-08-15T17:51:40.233Z,1534355500.233 [MassServo](FAULT): Invalid EZ Servo response:""
2018-08-15T17:51:40.233Z,1534355500.233 [MassServo](FAULT): Mass Shifter error waiting for homing. Uart error: serial timeout
2018-08-15T17:51:41.676Z,1534355501.676 [SBIT](IMPORTANT): Beginning Startup BIT
2018-08-15T17:51:41.696Z,1534355501.696 [CBIT](IMPORTANT): Beginning ground fault scan
2018-08-15T17:51:42.353Z,1534355502.353 [ElevatorServo](FAULT): Invalid EZ Servo response:""
2018-08-15T17:51:43.643Z,1534355503.643 [RudderServo](FAULT): Invalid EZ Servo response:""
2018-08-15T17:51:46.978Z,1534355506.978 [ElevatorServo](FAULT): Invalid EZ Servo response:""
2018-08-15T17:51:47.870Z,1534355507.870 [Aanderaa_O2](FAULT): Timed out starting
2018-08-15T17:51:48.317Z,1534355508.317 [RudderServo](FAULT): Invalid EZ Servo response:""
2018-08-15T17:51:48.328Z,1534355508.328 [CBIT](FAULT): Communications Fault in component: Aanderaa_O2
2018-08-15T17:51:48.746Z,1534355508.746 [Aanderaa_O2](FAULT): LCB fault: LCB Watchdog Reset. Invalid Command. Hardware Overcurrent Shutdown. Software Overcurrent. Current Limiter Activated.
2018-08-15T17:51:52.928Z,1534355512.928 [CBIT](IMPORTANT): Ground fault detected
mA:
CHAN A0 (Batt): -0.016407
CHAN A1 (24V): 0.046385
CHAN A2 (12V): -0.004313
CHAN A3 (5V): -0.002852
CHAN B0 (3.3V): -0.001498
CHAN B1 (3.15aV): -0.000564
CHAN B2 (3.15bV): -0.001481
CHAN B3 (GND): 0.000059
OPEN: 0.004162
Full Scale Calc: 4.765 mA, -1.589 mA
2018-08-15T17:52:06.094Z,1534355526.094 [CommandLine](IMPORTANT): got command ! echo 1 > /dev/loadB2
2018-08-15T17:52:21.632Z,1534355541.632 [SBIT](FAULT): Control surface position failure.
2018-08-15T17:52:35.213Z,1534355555.213 [SBIT](FAULT): Control surface position failure.
2018-08-15T17:52:35.645Z,1534355555.645 [CommandLine](IMPORTANT): got command configSet list
2018-08-15T17:52:35.645Z,1534355555.645 [CommandLine](IMPORTANT): Listing configuration overrides from Data/persisted.cfg
2018-08-15T17:52:35.646Z,1534355555.646 [CommandLine](IMPORTANT): AHRS_M2.loadAtStartup=0 bool;

2018-08-15T17:52:35.646Z,1534355555.646 [CommandLine](IMPORTANT): AHRS_M2.verbosity=1 count;

2018-08-15T17:52:35.646Z,1534355555.646 [CommandLine](IMPORTANT): DropWeight.loadAtStartup=0 bool;

2018-08-15T17:52:36.005Z,1534355556.005 [MissionManager](IMPORTANT): Started mission Startup
2018-08-15T17:52:56.519Z,1534355576.519 [CommandLine](IMPORTANT): got command configSet Aanderaa_O2.loadAtStartup 0.000000 bool persist
2018-08-15T17:52:56.520Z,1534355576.520 [CommandLine](IMPORTANT): configSet Aanderaa_O2.loadAtStartup requires a restart to take effect.
2018-08-15T17:52:59.726Z,1534355579.726 [CommandLine](IMPORTANT): got command restart application